How to stop rain from entering at the cuffs of my rain jacket?
So this is one of those things that I've grown so accustomed to that I've not really put any effort or thought into looking for a solution. I've just "dealt with it" to the point of ignoring it for so long now.
Almost all rain jackets provide an adjustable cuff via velcro or other means to cinch up around the wrist, but this barely impedes the invasion of moisture at that point. What is a method or piece of gear that will prevent water from dripping down the hands and wrist into the cuffs of a rain jacket when hands are horizontal or reaching above? Gloves are a quick thought but they will capture water when your hands are down and are unlikely to be worn in warm weather.
Just to head this one off: please no "buy a new rain jacket" answers. Even the best rain jackets will have this problem.
This post was sourced from https://outdoors.stackexchange.com/q/11189. It is licensed under CC BY-SA 3.0.
3 answers
You are accessing this answer with a direct link, so it's being shown above all other answers regardless of its score. You can return to the normal view.
I've never had too much trouble with a double cuff - a velcro or (better) elastic inner cuff and a loose outer. In the worst conditions, an elasticated inner cuff under a goretex glove with long elasticated wrist seals was good for anything short of immersion.
In the worst case a watersports dry cag would solve this. They have latex or neoprene wrist seals.
They're also rather impractical as rain jackets. Using them for inspiration instead might be better. My dry suit had slightly slack wrist seals for me. By cutting rings of spare latex wrist seals (like fat stiff rubber bands) and putting them over the top, the problem was solved. In fact just rubber bands would help and is an old-fashioned solution. If you have thin wrists or a bike with fat tyres, some bands of old inner tubes would do the trick. They could overlap the end of the sleeve and any glove as a sort of wrist gaiter.
Any tight wrist seal will make you hot.
This post was sourced from https://outdoors.stackexchange.com/a/11190. It is licensed under CC BY-SA 3.0.
0 comment threads
While working outside in the rain and when wearing a rain jacket, I have two simple solutions for keeping as dry as possible when the weather is miserable. I do not wear wrist bands because I like to have some ventilation. You cannot stop water from creeping inside, so I use latex gloves inside my regular gloves, this way my hands are reasonably dry. The second thing I do (only if the temperature is warm enough) is that I roll up my shirt sleeves to just past my elbows. At least this way I am able to stay dry. This little trick I've used for several years now and it works quite nicely. When I take my rain jacket off at least I am dry, although I will be a little humid. Rain gear in general is not breathable.
Note: If one is really desperate, there is the possibility of putting on long veterinary gloves under your rain jacket!
This post was sourced from https://outdoors.stackexchange.com/a/11191. It is licensed under CC BY-SA 3.0.
0 comment threads
As a Scot I did a lot of wet climbing, so am pretty familiar with the issue you've asked about!
I was careful to buy jackets with a good cuff, and I'd use absorbent sweat-bands on my wrists just inside the cuff to mop up any leakage.
I'd also roll or ruck up the arms of my inner layers so they were above the sweat bands and stayed pretty dry.
In torrential conditions, you might have to wring out the sweatbands every now and again on the belays!
If your jacket has a poor cuff, Chris H's idea of a rubber seal might be your best option - on its own or in combination with wrist bands. Though it will cut out all ventilation which causes its own issues with damp.
This post was sourced from https://outdoors.stackexchange.com/a/11224. It is licensed under CC BY-SA 3.0.
0 comment threads
0 comment threads